-
Tracking Bar Rails - 10ft Length x 24in Wide Section - Inverted steel angle track holds tire in place for through travel on V-Groove inverted tracking bars - Recommended for all surface and front wheel pull over- under conveyors.
-
Take Up Slide Tube with UHMW Bushing - Steel Tube - Used o Sonny's Spring Take-up and Air Tensioning Take-up Conveyors. - (2) Needed per conveyor.
-
Take Up Slide Shaft - 1-1/2in Diameter x 39-1/2in Long - Stainless Steel - Used o Sonny's Spring Take-up and Air Tensioning Take-up Conveyors. - (2) Needed per conveyor.
-
Sonny's Surface Conveyor Chain Tension Arm Slide Tube Weldment.
-
Sonny's Surface Conveyor Exit Sprocket End Cover Plate.
-
Extension Spring with End Hooks - 5in Length x 3/4in O.D. for MacNeil RG440 Conveyor ( 44-454-00 ) - 302 Stainless Steel
-
Hanna Conveyor Spring Retainer Cap Steel Weldment. ( Hanna # 720417 ) - Sonny's Replacement for Hanna.
-
Slider Passenger side Weldment for MacNeil RG440 Conveyor ( 44-039-00-YL )
-
Hanna Conveyor Slide Pads 2in x 2in x 1/8in - Set of 4 with Hardware. - ( Hanna # 148205 ) Sonny's Replacement for Hanna.
-
Sonny's Surface Conveyor Roller-up Base Pivoting Arm Shaft.
-
Rubber Bumper Stop - 1-3/4in O.D. x 1-5/8in Length for MacNeil RG440 Conveyor (44-081-00-PP ) Accepts Rod Course Thread Size; 5/8-11 - Used on MacNeil Safty Door Exit End.
-
GO switch leverless limit switch provides reliable, durable position sensing in the most demanding car wash conditions.
-
Fork Pivoting Bracket Steel for MacNeil RG440 Conveyor ( 44-052-00-YL ) 2 # required
-
Guides vehicle tire off at the exit end of the conveyor for a smoother transition - 5/16in Thick - Steel
-
Heco Gearbox Exit Drive Mounting Plate for Sonny's Surface Conveyor. Only used on Surface Conveyor, Plate Measurement 16in x 16in
-
Heco Gearbox Exit Drive Mounting Plate for Spring and Air Take-up Conveyor. Sonny's
-
Fiberglass Grating Square Mesh Molded with Non-Skid Surface - Dark Gray - 3ft Width x 10ft Length x 1-1/2in Thickness
-
Fiberglass Grating Solid Flat Decktop with Grit Surface - Dark Gray - 3ft Width x 10ft Length x 1-5/8in Thickness
-
Sonny's Surface Conveyor Roller-up Fork with UHMW Bushing
-
Roller Up Fork Triangle Style for Air Take Up Conveyor - 1-1/4in Shaft stainless steel to accept bearing hanger with steel triangle fork assembly.
-
Fork Pivot Bracket for Air Take-Up. - Used on roller up fork with cylinder to activate roller up fork.
-
Air Take-up Fork Hanger with bushing, Passengerside. ( Used on conveyor Fall 2007 to Spring of 2008 )
-
Fork Hanger with UHMW Bushing - Used on Spring Take Up - Material; Steel Painted.
-
Fork Hanger with 1-1/4in AMI Bearing - Used on Air Take Up - Material; - Steel Painted.
-
Exit Trap Door Plate - Dimension; 6in Length x 13in Width x 3/8in - Used on Sonny's Conveyor Exit End Trap Door
-
Exit Safety Door with zerk fittings for MacNeil RG440 Conveyor (44-088- 10-YL ) Sonny's Replacement for MacNeil Conveyor.
-
Door Exit Service Cover Plate for MacNeil RG440 Conveyor 19-3/4in Length x 11in Width ( MacNeil # 44-089-00-YL ) Sonny's Replacement for MacNeil
-
Door Hinge Pin Exit - Dimension; 15-1/2in Length x 9/16in Diameter - Used on Sonny's and Hanna Conveyor Trap Door with Hinge Pin Design.
-
Hanna Exit Trap Door with Roller Wheel and Axle. - New Hanna Style - Dimension; 13in Width x 9-3/4in Length - Hinge Pin 9-3/4in Width x 9/16 Diameter ( Hanna # 723288 ) Sonny's Replacement for Hanna Conveyor.
-
Hanna Exit Service Trap Door Cover Plate 11in Length x 15in Width without Hardware Holes. ( Hanna # 256008 ) Sonny's Replacement for Hanna Conveyor.