-
Fiberglass Grating Solid Flat Decktop with Grit Surface - Dark Gray - 3ft Width x 10ft Length x 1-5/8in Thickness
-
Guides vehicle tire off at the exit end of the conveyor for a smoother transition - 5/16in Thick - Steel
-
GO switch leverless limit switch provides reliable, durable position sensing in the most demanding car wash conditions.
-
Fiberglass Grating Square Mesh Molded with Non-Skid Surface - Dark Gray - 3ft Width x 10ft Length x 1-1/2in Thickness
-
Spring Take Up Carriage Weldment Frame Steel. - Used on Sonny's Spring Take-up entrance end section.
-
Carriage Weldment Tension Frame Steel - Used on Shallow Conveyor.
-
UHMW Rail Cover Banana Peel Yellow 15ft Length. - Shipped Via Truck Only
-
Slider Passenger side Weldment for MacNeil RG440 Conveyor ( 44-039-00-YL )
-
Take Up Slide Shaft - 1-1/2in Diameter x 39-1/2in Long - Stainless Steel - Used o Sonny's Spring Take-up and Air Tensioning Take-up Conveyors. - (2) Needed per conveyor.
-
Sonny's Surface Conveyor Chain Tension Arm Slide Tube Weldment.
-
Tracking Bar Rails - 10ft Length x 24in Wide Section - Inverted steel angle track holds tire in place for through travel on V-Groove inverted tracking bars - Recommended for all surface and front wheel pull over- under conveyors.
-
Roller Up Fork Triangle Style for Air Take Up Conveyor - 1-1/4in Shaft stainless steel to accept bearing hanger with steel triangle fork assembly.
-
Exit Safety Door with zerk fittings for MacNeil RG440 Conveyor (44-088- 10-YL ) Sonny's Replacement for MacNeil Conveyor.
-
Sonny's Surface Conveyor Exit Sprocket End Cover Plate.
-
Fork Hanger with 1-1/4in AMI Bearing - Used on Air Take Up - Material; - Steel Painted.
-
Door Exit Service Cover Plate for MacNeil RG440 Conveyor 19-3/4in Length x 11in Width ( MacNeil # 44-089-00-YL ) Sonny's Replacement for MacNeil
-
Conveyor - Steel Replacement Weldment Part - Guide Angle Middle Shelf Angle Bar Weldment
-
Conveyor - Steel Replacement Weldment Part - Top Door Rest Angles - Top shelf angle bar precut weldment size 3in x 5in angle x 1/2in thickness. (One Set)
-
UHMW Rail Cover 3in x 3in x 1/2in Yellow Angle x 15ft Length. - Shipped Via Truck Only
-
Sonny's Surface Conveyor Roller-up Fork with UHMW Bushing
-
Hanna Exit Service Trap Door Cover Plate 11in Length x 15in Width without Hardware Holes. ( Hanna # 256008 ) Sonny's Replacement for Hanna Conveyor.
-
Air Take-up Fork Hanger with bushing, Passengerside. ( Used on conveyor Fall 2007 to Spring of 2008 )
-
Hanna Exit Trap Door with Roller Wheel and Axle. - New Hanna Style - Dimension; 13in Width x 9-3/4in Length - Hinge Pin 9-3/4in Width x 9/16 Diameter ( Hanna # 723288 ) Sonny's Replacement for Hanna Conveyor.
-
Take Up Slide Tube with UHMW Bushing - Steel Tube - Used o Sonny's Spring Take-up and Air Tensioning Take-up Conveyors. - (2) Needed per conveyor.
-
Exit Trap Door Plate - Dimension; 6in Length x 13in Width x 3/8in - Used on Sonny's Conveyor Exit End Trap Door
-
Heco Gearbox Exit Drive Mounting Plate for Sonny's Surface Conveyor. Only used on Surface Conveyor, Plate Measurement 16in x 16in
-
Heco Gearbox Exit Drive Mounting Plate for Spring and Air Take-up Conveyor. Sonny's
-
Fork Pivot Bracket for Air Take-Up. - Used on roller up fork with cylinder to activate roller up fork.
-
Banana Peel, 5ft Yellow UHMW Extrusion -Ships Via FedEx *This part replaces old part #20002313